Ring & Plug Thread Gages  
 
Call 616 954 6581 for Thread Gages
About Ring & Plug Thread GagesUsed - Surplus Ring & Plug Thread GagesRing & Plug Thread Gage Technical InformationRing & Plug Thread Gage CatalogsContact Ring & Plug Thread GagesBookmark

 

 
 
 
 
 

Enersol S15 Force/Torque Fitting Assembly Machine

 
Image Viewer

ENERSOL S15 FORCE/TORQUE FITTING ASSEMBLY MACHINE for ISO 594

NOTE:
ISO 594 has been rescinded and replaced by ISO 80369-7. Because of the change from ISO 594 into ISO 80369-7; all tests per ISO 594 should now be switched to tests per ISO 80369-7 (ISO 80369-20).

NOTE:
Enersol Model S15 Fitting Assembly Device was specifically designed for ISO 594. Enersol Model S15 Fitting Assembly Device has been discontinued and replaced with the Enersol Model S15A Connector Assembly Device. Enersol Model S15A Connector Assembly Device has been designed specifically for ISO 80369 tests as listed in ISO 80369-20. Enersol Model S15A Connector Assembly Device is not backward compatible to ISO 594. Enersol Model S15 Fitting Assembly Device can be adapted to work with ISO 80369-20.

NOTE:
Contact us if you desire to purchase the discontinued Enersol Model S15 Fitting Assembly Device. The Enersol Model S15 Fitting Assembly Device is only built on special request.

NOTE:
Contact us if you own Enersol Model S15 Fitting Assembly Device and wish it upgraded to work with both ISO 594 and ISO 80369-20. To accomplish we will work with you to get the Enersol Model S15 Fitting Assembly Device returned Enersol. Enersol will make the appropriate modifications and return the upgraded device to you.

NOTE:
Contact us if you own Enersol Model S15 Fitting Assembly Device and wish it converted into the Enersol Model S15A Connector Assembly Device. To accomplish we will work with you to get the Enersol Model S15 Fitting Assembly Device returned Enersol. Enersol will make the appropriate modifications and return the converted device to you. Enersol Model S15A Connector Assembly Device is not backward compatible to ISO 594.

Force/Torque Fitting Assembly Machine
The Enersol S15 Force/Torque Fitting Assembly Machine is the base machine which is needed for all of the ISO 594 specified tests. The Force/Torque Fitting Assembly Machine is made from aluminum and hardened steel. The Force/Torque Fitting Assembly Machine has a durable and attractive anodized finish. The Force/Torque Fitting Assembly Machine has been designed to be compact and easy to use, with no other requirements like an electrical supply or compressed air, etc.

The Force/Torque Fitting Assembly Machine is an integral part of Luer, needle and syringe testing and is used to assemble reference fittings to samples under test. It is also used to assemble needle hubs with syringes for tests in ISO8537. Known axial and side weights are required for preparation of samples and are supplied with the kit.

The Force/Torque Fitting Assembly Machine is used for preparing samples for tests such as liquid leakage, air leakage, separation force, ease of assembly, stress cracking, unscrewing torque and resistance to overriding. The Force/Torque Fitting Assembly Machine comes with a range of axial and side weights for use with ISO594-1, ISO594-2, ISO7886 series (Parts 1-4) and ISO8537.

Uses for the Force/Torque Fitting Assembly Machine
Below is a list of tests which are best accomplished by using the Force/Torque Fitting Assembly Machine.

ISO 594/1 Liquid Leakage Test as defined in paragraph 4.2*
To conduct the Liquid Leakage Test found in ISO 594/1 paragraph 4.2 the following Enersol products are required:
S11 - Male Reference Fitting ISO594/1 Figure 5 and/or
S12 - Female Reference Fitting ISO594/1 Figure 4
S15 - Force/Torque Fitting Assembly Machine
S16 - Liquid Leakage Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 4; Annex C Falling drop positive-pressure liquid leakage test method:
This liquid leakage test method is performed in the same manner as in the ISO 594- series.

ISO 594/1 Air Leakage Test as defined in paragraph 4.3*
To conduct the Air Leakage Test found in ISO 594/1 paragraph 4.3 the following Enersol products are required:
S11 - Male Reference Fitting ISO594/1 Figure 5 and/or
S12 - Female Reference Fitting ISO594/1 Figure 4
S15 - Force/Torque Fitting Assembly Machine
S17 - Air Leakage Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 4; Annex D Subatmospheric-pressure air leakage test method:
This subatmospheric-pressure air leakage test method is a new test method that was not part of the former ISO 594- series. The ISO 594- series test method for subatmospheric-pressure (ISO 594-1, 5.3 and ISO 594-2, 5.3) creates an unspecified subatmospheric test pressure and asks the observer to look for continued formation of bubbles of an unspecified size.

ISO 594/1 Separation Force Test as defined in paragraph 4.4*
To conduct the Separation Force Test found in ISO 594/1 paragraph 4.4 the following Enersol products are required:
S11 - Male Reference Fitting ISO594/1 Figure 5 and/or
S12 - Female Reference Fitting ISO594/1 Figure 4
S15 - Force/Torque Fitting Assembly Machine
S18 - Separation Force Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 5; Annex F Resistance to separation from axial load test method:
This resistance to separation from axial load test method is performed in the same manner as in the ISO 594- series. The title and principle have been elaborated to describe the intent of the test.

ISO 594/1 Stress Cracking Test as defined in paragraph 4.5*
To conduct the Stress Cracking Test found in ISO 594/1 paragraph 4.5 the following Enersol products are required:
S11 - Male Reference Fitting ISO594/1 Figure 5 and/or
S12 - Female Reference Fitting ISO594/1 Figure 4
S15 - Force/Torque Fitting Assembly Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 4; Annex E Stress cracking test method:
This stress cracking test method is performed in the same manner as in the ISO 594- series. The acceptance criteria have been changed to require passing a functional leak test after the stress cracking
test has been performed.

ISO 594/2 Liquid Leakage Test as defined in paragraph 4.2.1*
To conduct the Liquid Leakage Test found in ISO 594/2 paragraph 4.2.1 the following Enersol products are required:
S07 - Male Reference Fitting ISO594/2 Figure 5 and/or
S09 - Female Reference Fitting ISO594/2 Figure 7
S15 - Force/Torque Fitting Assembly Machine
S16 - Liquid Leakage Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 4; Annex C Falling drop positive-pressure liquid leakage test method:
This liquid leakage test method is performed in the same manner as in the ISO 594- series.

ISO 594/2 Air Leakage Test as defined in paragraph 4.2.2*
To conduct the Air Leakage Test found in ISO 594/2 paragraph 4.2.2 the following Enersol products are required:
S07 - Male Reference Fitting ISO594/2 Figure 5 and/or
S09 - Female Reference Fitting ISO594/2 Figure 7
S15 - Force/Torque Fitting Assembly Machine
S17 - Air Leakage Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 4; Annex D Subatmospheric-pressure air leakage test method:
This subatmospheric-pressure air leakage test method is a new test method that was not part of the former ISO 594- series. The ISO 594- series test method for subatmospheric-pressure (ISO 594-1, 5.3 and ISO 594-2, 5.3) creates an unspecified subatmospheric test pressure and asks the observer to look for continued formation of bubbles of an unspecified size.

ISO 594/2 Separation Force Test as defined in paragraph 4.3*
To conduct the Separation Force Test found in ISO 594/2 paragraph 4.3 the following Enersol products are required:
S08 - Male Reference Fitting ISO594/2 Figure 6 and/or
S10 - Female Reference Fitting ISO594/2 Figure 8
S15 - Force/Torque Fitting Assembly Machine
S18 - Separation Force Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 5; Annex F Resistance to separation from axial load test method:
This resistance to separation from axial load test method is performed in the same manner as in the ISO 594- series. The title and principle have been elaborated to describe the intent of the test.

ISO 594/2 Unscrewing Torque Test as defined in paragraph 4.4*
To conduct the Unscrewing Torque Test found in ISO 594/2 paragraph 4.4 the following Enersol products are required:
S08 - Male Reference Fitting ISO594/2 Figure 5 and/or
S10 - Female Reference Fitting ISO594/2 Figure 7
S15 - Force/Torque Fitting Assembly Machine
S19 - Unscrewing Force Test Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 5; Annex G Resistance to separation from unscrewing test method:
This resistance to separation from unscrewing test method is performed in the same manner as the ISO 594- series. The title and principle have been elaborated to describe the intent of the test.

ISO 594/2 Ease of Assembly Test as defined in paragraph 4.5*
To conduct the Ease of Assembly Test found in ISO 594/2 paragraph 4.5 the following Enersol products are required:
S07 - Male Reference Fitting ISO594/2 Figure 5 and/or
S09 - Female Reference Fitting ISO594/2 Figure 7
S15 - Force/Torque Fitting Assembly Machine
*NOTE: This test is not required in ISO 80369-20. Rationale given in Annex A; Paragraph A.2 ; Page 3; Clause 1 Scope:
The ease of assembly test method that was part of the ISO 594- series has been removed as a requirement from the application parts of ISO 80369 and is not present in this part of ISO 80369. The acceptance criterion of the ISO 594- series for ease of assembly was subjective. It was under-defined for a standardized test method, i.e. “a satisfactory fit” is not repeatable. Furthermore, the intent of the ease of assembly test was to ensure that the user can complete the connection using the mating halves of the connector. This requirement is satisfied by the requirement for usability validation for all new connectors being added to ISO 80369. Therefore, the ease of assembly test method has been omitted from the ISO 80369- series of standards.

ISO 594/2 Resistance to Overriding Test as defined in paragraph 4.6*
To conduct the Resistance to Overriding Test found in ISO 594/2 paragraph 4.6 the following Enersol products are required:
S08 - Male Reference Fitting ISO594/2 Figure 6 and/or
S10 - Female Reference Fitting ISO594/2 Figure 8
S15 - Force/Torque Fitting Assembly Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 5; Annex H Resistance to overriding test method:
This resistance to overriding test method is performed in the same manner as the ISO 594- series.

ISO 594/2 Stress Cracking Test as defined in paragraph 4.7*
To conduct the Stress Cracking Test found in ISO 594/2 paragraph 4.7 the following Enersol products are required:
S07 - Male Reference Fitting ISO594/2 Figure 5 and/or
S09 - Female Reference Fitting ISO594/2 Figure 7
S15 - Force/Torque Fitting Assembly Machine
*NOTE: Per ISO 80369-20; Annex A; Paragraph A.2; Page 4; Annex E Stress cracking test method:
This stress cracking test method is performed in the same manner as in the ISO 594- series. The acceptance criteria have been changed to require passing a functional leak test after the stress cracking
test has been performed
.

Price Lists:
Enersol ISO 594 Reference Connectors(Fittings)
Enersol Test Machines

Disclaimer:
This data is provided for general information only. The intention is to provide accurate information; regardless; errors may exist in the supplied information. If accuracy is critical, base your final decisions on the data provided in the root documents which are usually copyrighted documents. To purchase a copy of an engineering document visit an Authorized Reseller.

Comments:
Original Posting: 5/11/2013
Last Revision: 6/14/2016
Error corrections in, or comments about, the above data can be sent to: gageguy@gagecrib.com

 

About UsUsed SurplusTech InfoCatalogsContact UsBookmark
 

 

Top

Gage Crib Worldwide, Inc.
6701 Old 28th St SE, Suite B
Grand Rapids, MI 49546-6937
Phone: 001-616-954-6581 • Fax: 001-616-954-6583
CONTACT  FORMS & INFO

Copyright © 2002-2017 Ring & Plug Thread Gages. All rights reserved.